We have collected the most relevant information on 6v6 Audio Amplifier. Open the URLs, which are collected below, and you will find all the info you are interested in.
6V6 Audio Amp parade - Ohio University
https://people.ohio.edu/postr/bapix/6V6amps.htm
A tale of three 6V6 Audio Amps. Revisiting a homebrew audio amplifier Some years ago, as a teenager of 15, I decided to homebrew an audio amp I had seen in an article in a 1958 Radio-TV Experimenter magazine. The article showed construction of the Arkay A-12 Hi-Fi amplifier kit and was complete with schematic and under-chassis pictorial. The set had push-pull 6V6GT output …
6P6P (6V6) Push-Pull Audio Amplifier
http://www.r-type.org/articles/art-272.htm
The KT66 is widely regarded as the finest audio valve ever designed, however, for the 10 Watt class the 6V6 family is hard to beat. The amplifier Kit as advertised on ebay. The author has plans for a pair of mono-bloc 6V6 push pull amplifiers with Hammond output transformers and DC-DC converts for both heater supply and main HT - all powered from a 19.5 Volt 'laptop brick' …
An Experimental 6V6 Single Ended Ultra Linear Audio Amplifier
http://www.r-type.org/articles/art-275.htm
The RMS power to a dummy load was not spectacular, however, the subjective performance in a 4 x 7 metre room was excellent. The amplifier was tested with an original metal 6V6 and the Brimar 6V6GT as well as the KT66. Worth a build. The KT66 had a cathode current of 60 mA without the 7 Watt transformer saturating.
DIY 6V6 SE-UL Tube Amplifier Schematic - Lacewood
https://diyaudioprojects.com/Schematics/SE-6V6-Amp-Lacewood-Schematic/
DIY Single-Ended Ultra-Linear 6V6 Tube Amplifier. This amp is designed to provide high quality music for an office or small den. It uses two 6V6 tubes in a single-ended (SE) ultra-linear (UL) configuration with a warm 6SN7 driver to give great music quality. The power transformer and power chokes are made by Hammond and the output transformers are made …
DIY Push-Pull (PP) 6V6 / 6V6GT Tube Amplifier Schematic
https://diyaudioprojects.com/Schematics/DIY-Push-Pull-PP-6V6-Tube-Amplifier/
This 6V6 amp was built following the push-pull (PP) EL84 / 6V6 Dynaco A-410 output transformer schematic. There are a few minor deviations from the original schematics. Instead of Dynaco transformers, Hammond 1608A audio output transformers and a Hammond 272HX power transformer were used. A 5Y3 rectifier would have been too small for a stereo …
Push-Pull 6V6 Amplifier | Evil Science Audio
https://evilscienceaudio.com/2013/10/31/push-pull-6v6-amplifier/
Push-Pull 6V6 Amplifier This amplifier was a gift to my father-in-law for Christmas a few years back. It is a distributed load push-pull output topology called “Ultra-Linear” back in the day. That is driven by a direct-coupled split-load phase inverter, preceded by a single gain stage, all using the common 12AU7.
The 6V6 Marblewood Amp | Cascade Tubes
https://www.cascadetubes.com/the-6v6-marblewood-amp/
Total current load for the amp with 6V6s is about 95mA. At 350Ω this equates to a power dissipation of about 3.16W. I settled on a nice 5W wire wound resistor shown below. With this installed both 6V6s were showing 16V cathode bias values and plate voltages of 272v.
Now you know 6v6 Audio Amplifier
Now that you know 6v6 Audio Amplifier, we suggest that you familiarize yourself with information on similar questions.
