We have collected the most relevant information on Audio Codes Factory Default. Open the URLs, which are collected below, and you will find all the info you are interested in.
IP Phone: Restoring Phone to Factory Defaults - …
https://www.audiocodes.com/media/14547/audiocodes-quick-reference-guide-restoring-ip-phone-to-factory-defaults.pdf
AUDIOCODES SHALL NOT BE HELD LIABLE FOR ANY INACCURACIES. Quick Reference Guide Restoring Defaults Using the Phone’s Screen To restore the phone’s factory defaults using the phones screen: 1. Press the Menu key 2. Scroll down to Administration and press OK 3. Enter the Admin password (default 1234) followed by OK 4.
Quick Setup Guide - AudioCodes
https://www.audiocodes.com/media/12879/ltrt-10702-mediant-500l-gateway-e-sbc-quick-guide.pdf
Use the device's factory default IP address (192.168.0.2/24 and Default Gateway 0.0.0.0) to initially access the device's Web-based management interface and then change it to suit your networking addressing scheme for subsequent connectivity. 1. Using a CAT-5e/6 straight-through RJ-45 Ethernet cable, connect the device's Ethernet port GE LAN #1
AudioCodes™
https://www.audiocodes.com/media/2504/ltrt-32301-mp-20x-frequently-asked-questions.pdf
AudioCodes Customer Support Page 10 Default Configuration Q1: How do I restore MP-20x to factory default settings? A: You can restore MP-20x to default settings using one of the following methods: Web interface: a) Logon to the Web interface. b) Access the ‘Restore Defaults’ screen (Advanced menu > Restore Defaults icon). c) Click OK.
How to Factory Reset a AudioCodes Mediant 1000 E-SBC with ...
https://myworldofit.net/?p=6801
Published 27 May, 2014 | By James Preston. If you have a shiny new AudioCodes Mediant 1000 E-SBC with a CRMX-C CPU module and a need to factory reset it then this is the guide for you! Looking at the front of the SBC (photo above) just to the right hand side of the second network port status light is a tiny little hole – perfect for a paperclip. Push and hold the …
AudioCodes MP114/118 (Edge) - Zenitel Wiki
https://wiki.zenitel.com/wiki/AudioCodes_MP114/118_(Edge)
The AudioCodes MP-114/118 VoIP Gateway comes with default network parameters (factory default parameters). The default IP address is 10.1.10.11. You can also load factory network parameters and reset the username and password to its default settings (username: Admin , password: Admin ) by following these steps:
AudioCodes Mediant 1000 - Zenitel Wiki
https://wiki.zenitel.com/wiki/AudioCodes_Mediant_1000
Configure Network Parameters. The AudioCodes Mediant 1000 VoIP Gateway comes with default network parameters (factory default parameters). Before you can set up the gateway in the network, you have to change the default IP address to a …
C470HD IP Phone - AudioCodes
https://www.audiocodes.com/media/15639/c470hd-ip-phone-for-microsoft-teams-users-and-administrators-manual.pdf
AudioCodes Device Management and AudioCodes Redirect Server for ... Only if the phone is restored to default settings will it be necessary to repeat this. Configuring Device Settings The section familiarizes you with the phone’s settings.
Mediant™ 1000B Gateway & E-SBC - AudioCodes
https://www.audiocodes.com/media/13746/mediant-1000b-gateway-e-sbc-quick-guide.pdf
Reset pinhole button for resetting the device or restoring it to factory defaults. To restore to defaults, press and hold down the button for at least 15 seconds (but no more than 25 seconds). Gigabit Ethernet LAN interface ports (RJ-45) for connecting IP phones, computers, or switches. The ports support 1+1 Ethernet port redundancy
Mediant™ 800 Gateway and E-SBC - AudioCodes
https://www.audiocodes.com/media/13726/mediant-800-gateway-e-sbc-quick-guide.pdf
1 | Page Mediant™ 800 Gateway and E-SBC Quick Setup Guide Welcome Congratulations on purchasing your AudioCodes Mediant 800 Gateway and Enterprise Session Border Controller (E-SBC), hereafter, referred to as the device!This Quick Guide applies to hardware revisions B and C. This document is intended to provide basic setup instructions for …
User's Manual - AudioCodes
https://www.audiocodes.com/media/10460/ltrt-71405-mgcp-megaco-mediapack-series-users-manual-ver-66.pdf
Version 6.6 . June 2014 . Document # LTRT-71405 . User's Manual . MP-1xx & MP-124 . MediaPack™ Series . Analog VoIP Media Gateways . MGCP & MEGACO Protocols
Now you know Audio Codes Factory Default
Now that you know Audio Codes Factory Default, we suggest that you familiarize yourself with information on similar questions.
