We have collected the most relevant information on Audiocodes Dtmf Transporttype. Open the URLs, which are collected below, and you will find all the info you are interested in.
AudioCodes Quick Reference Guide
https://www.audiocodes.com/media/14274/audiocodes-quick-reference-guide-voice-quality-troubleshooting-for-session-border-controllers-sbcs-and-gateways.pdf
AUDIOCODES SHALL NOT BE HELD LIABLE FOR ANY INACCURACIES. Quick Reference Guide From RFC2833 volume: For DTMF digits and other events representable as tones, this field describes the power level of the tone, expressed in dBm0 after dropping the sign. Power levels range from 0 to -63 dBm0. The range of valid DTMF is from 0 to -36 dBm0 (must
CAS Protocol Tables - AudioCodes
https://www.audiocodes.com/media/12391/ltrt-28615-cas-protocol-table-configuration-note-ver-72.pdf
state. INIT_DTMF_DIAL defines the Ontime and Off--time for the DTMF digits generated towards the PSTN. Refer to the detailed list in UserProt_defines_xxx.h and in the sample protocol text file (supplied CAS files). Refer to the following ST_INIT detai led explanation.
Audio Codes MP-118 FXO
https://social.technet.microsoft.com/Forums/en-US/4fc70a55-5abb-44ba-8d45-e582fd056487/audio-codes-mp118-fxo
Actually, the FXO Settings -->VoiceMail --> SMDI or DTMF directly affect the Diversion header. SMDI is a standard, and if set up, the diversion is created automatically. For Voice Mail the DTMF Reason fields create the diversion header.
Solved - Working configuration for Audiocodes mp118 …
https://www.3cx.com/community/threads/working-configuration-for-audiocodes-mp118-fxs.62336/
Also take note of a couple of settings that you may need to be aware of when setting up the device:GW and IP to IP > DTMF and Supplementary > DTMF & Dialing Change the Max Digits In Phone Number to an appropriately high number - this can cause problems as it is not set as such by default. So longer digit numbers will be rejected.
AudioCodes Mediant 1000 Configuration - Altigen
https://know.altigen.com/attachments/1266/AudioCodes-Mediant1000.pdf
AudioCodes Mediant 1000 Configuration Guide for MAXCS 8.5 Page 11 of 27 4. On row 1, set Proxy Address to the MaxCS server's IP address and port 5060. Figure 10: For Proxy Set ID 0, configure row 1 parameters 5. Set Transport Type to UDP. 6. Set Enable Proxy Keep Alive to Using Options. 7. Click Submit. Set VoIP Coder Parameters
HOWTO: Setup an Audiocodes Mediant 500L with Zetafax
https://www.equisys.com/Support/Technotes/howto-setup-an-audiocodes-mediant-500l-with-zetafax
6. From the V.34 Modem Transport Type dropdown list, select Enable bypass. 7. Click Submit to apply your changes. 8. Click on the ‘BURN’ option at the top of the web page to save changes to flash memory. Configure Proxy Sets Table. You will need to configure your AudioCodes gateway to communicate with your Zetafax Server.
MAX Communication Server Release 8.0 AudioCodes MP-11x ...
https://know.altigen.com/attachments/1194/MP118_TLS.pdf
MaxCS 8.0 AudioCodes MP-1xx Gateway Configuration Guide Page 9 of 57 12. Select VoIP > SIP Definitions > General Parameters. Figure • Make sure that NAT IP Address is 0.0.0.0. • Set Enable Early Media to Disable. • Set SIP Transport Type to UDP. • Set SIP UDP Local Port to 10060. • Set SIP Destination Port to 10060.
Now you know Audiocodes Dtmf Transporttype
Now that you know Audiocodes Dtmf Transporttype, we suggest that you familiarize yourself with information on similar questions.
