We have collected the most relevant information on Cisco Ata Audio Parameters. Open the URLs, which are collected below, and you will find all the info you are interested in.
Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor ...
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccp3_0/sccpaape.html#:~:text=%E2%80%A2%20The%20Cisco%20ATA%20uses%20the%20following%20parameter,separated%20by%20commas%20%E2%80%93%20Boolean%20%281%20or%200%29
Cisco ATA 186 and Cisco ATA 188 Analog Telephone …
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccp3_0/sccpaape.html
Cisco ATA 186 and Cisco ATA 188 Analog Telephone …
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sip/sip30ad/SIP88APE.html
Two types of extended format exist for the Cisco ATA tone parameters: • Extended Format A—This format can be used for the following tone parameters: – DialTone – BusyTone – RingbackTone – CallWaitTone – AlertTone • Extended Format B—This format can be used for the following tone parameters: – ReorderTone – SITone . Extended Format A
Cisco ATA 191 Analog Telephone Adapter Administration ...
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/191/english/admin-guide/at91_b_ata191-admin-guide/at91_b_ata191-admin-guide_chapter_011.html
Set the following ATA 191 parameters from port 1 only: IVR Password, CDP, Impedance, Input/Output Audio Level, Timers, and Call Sequence. Setting these parameters from port 2 has no effect. Table 3.
Configuring the ATA 187 - Cisco
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/187/1_0/english/administration/guide/sip/187adm80/a187_ag3conf.pdf
Cisco ATA 187 Analog Telephone Adaptor Administration Guide for SIP (Version 1.0) ... You can configure an audio and/or visual alert for the primary line on the phone. This alert notifies the users that ... Note Some ATA 187 parameters are set from port 1 only. Setting the parameters from port 2 will have no
Cisco ATA 191 and ATA 192 Analog Telephone Adapter ...
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/19x/3PCC/english/provguide/at1x_b_ata191-ata192-mpp-prov/at1x_b_ata191-ata192-mpp-prov_chapter_0101.html
Voice Parameters Voice Parameter Numbering Certain types of parameters apply to multiple elements, such as users and lines. In the configuration file, the parameter name is appended with a number, such as <Line_Enable_1> and <Line_Enable_2>. To understand this numbering system, use the following key: 1—User 1 or Line1 (PHONE1 port)
SPA112 ATA - No audio on incoming calls - Cisco Community
https://community.cisco.com/t5/atas-gateways-and-accessories/spa112-ata-no-audio-on-incoming-calls/td-p/2710269
On ATA Information page I can see hook state for line 1 changes from ON to OFF, but still no audio. After a while the caller is connected to the voicemachine. I have tried to change NAT Mapping/ NAT Keep Alive and a lot of other parameters but without success.
ATA112: No audio for incoming calls - Cisco Community
https://community.cisco.com/t5/atas-gateways-and-accessories/ata112-no-audio-for-incoming-calls/td-p/4030448
This port range is defined into Voice -> SIP -> RTP Parameters -> RTP Port Min / RTP Port Max. If it's opened, the RTP stream from the server will succeed to reach your SPA112 even before the phone begins to ring. Keep us informed !
ATA Passthrough Configuration - Voice Gateways
https://www.ccexpert.us/voice-gateways/ata-passthrough-configuration.html
The specific parameter used to set each port for fax mode is the AudioMode parameter. This parameter is a 32-bit value, where the lower 16 bits apply to the first line, and the upper 16 bits apply to the second line. These two ports can be configured independently. Table 9-7 defines the bits that make up the AudioMode parameter.
Voice Menu Codes - Cisco
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sip/sip30ad/SIP88APF.pdf
Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide for SIP (version 3.0) OL-4654-01 Appendix B Voice Menu Codes Table B-2 lists configuration codes. Table B-2 Cisco ATA Voice Menu Codes—Configuration Parameters Option Voice Menu Code Description Alternate NTP IP address 78 IP address of the alternate NTP server
Now you know Cisco Ata Audio Parameters
Now that you know Cisco Ata Audio Parameters, we suggest that you familiarize yourself with information on similar questions.
