We have collected the most relevant information on Cisco Ip Communicator No Audio Device. Open the URLs, which are collected below, and you will find all the info you are interested in.
Cisco Bug: CSCsa65866 - Communicator-'No Compatible Sound ...
https://quickview.cloudapps.cisco.com/quickview/bug/CSCsa65866#:~:text=Description%20%28partial%29%20Symptom%3A%20IP%20Communicator%20Audio%20Tuning%20Wizard,no%20compatible%20sound%20devices%20installed%20on%20this%20computer.%22
IP Communicator Error Message: There are No ... - Cisco
https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/ip-communicator/107347-IP-communicator.html
Solved: Cisco IP Communicator - No Devices Detected ...
https://community.cisco.com/t5/ip-telephony-and-phones/cisco-ip-communicator-no-devices-detected/td-p/2073804
To fix the issue try the following: 2-Verify that the intended recording/playback devices for use with IP Communicator have THE SAME NAME ex: Realtek High-Definition Audio Device again, in both devices (PLAYBACK AND RECORDING), otherwise, you can change it under the "propieties" dialog.
Cisco Bug: CSCsa65866 - Communicator-'No Compatible Sound ...
https://quickview.cloudapps.cisco.com/quickview/bug/CSCsa65866
Description (partial) Symptom: IP Communicator Audio Tuning Wizard shows nothing in the dropdown selection boxes, and when Communicator is launched, it gives a messages stating: "There are no compatible sound devices installed on this computer." Conditions: Attempting to install/use IP Communicator on a system that has different names …
Cisco IP Communicator - Audio Issues - TeamDynamix
https://volstate.teamdynamix.com/TDClient/1994/Portal/KB/ArticleDet?ID=111924
Right click on the device, then click on "Set as Default Device". Then click "OK" or "Apply" to save the settings. Step 2: Adjusting Audio Settings Within CIPC Run Cisco IP Communicator and locate the Preferences button (circled in red). Click on Audio Tuning Wizard. Set all of these individual categories as Default Windows Audio Device.
Troubleshooting Cisco IP Communicator
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cipc/7_0/english/user/guide/CIPCUG70/ipcugts.pdf
Cisco IP Communicator, choose the adapter that is most likely to provide permanent connectivity or is always enabled—even if it is not plugged in. Your system administrator can tell you which adapter to choose. The network adapter setting allows Cisco IP Communicator to identify itself to the network; it is not used for audio transmission.
Using Headsets and Other Audio Devices with Cisco …
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cipc/7_0/english/user/guide/CIPCUG70/ipcugdev.pdf
Cisco IP Communicator uses speakerphone mode as the default audio mode. Cisco IP Communicator responds to softkeys, speed-dial buttons, and other features by routing audio through the active mode. You can use a headset with all of the controls on Cisco IP Communicator, including the Volume button and the Mute button.
No Audio Cisco IP Communicator ver 8.6.6.0 - reddit
https://www.reddit.com/r/Cisco/comments/nq39pj/no_audio_cisco_ip_communicator_ver_8660/
Hello, I am using Cisco IP Communicator ver 8.6.6.0 and can get dial tone, the phone rings and connects, but I cannot hear the other person and the other person cannot hear me. I am using in conjunction with a FortiClient VPN. This has been tested on multiple recipients, the client has been uninstalled and reinstalled cleanly, PC and drivers all updated, network settings have been …
Cisco IP Communicator on Virtual Machine? - UC Collabing
https://www.uccollabing.com/cisco-ip-communicator-on-virtual-machine/
On your System > Go to Run > Type “mstsc” Enter the IP Address of Microsoft Windows Click Show Options Click on Local Resources Tab Click on Remote Audio Settings Remote Audio Playback > Radio Check “Play on Remote Computer” Click on OK and Click on Connect Right Click on Cisco IP Communicator and “Run as Administrator”
User Guide for Cisco IP Communicator Release 7.0 ...
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cipc/7_0/english/user/guide/CIPCUG70/ipcugts.html
Choose your sound card instead. If you want one device for sound playback and a different device (such as the VT camera microphone) for sound recording, in Cisco IP Communicator, right-click > Preferences > Audio tab. Choose Default Windows Audio Device from the drop-down list for one or more settings. and click OK.
User Guide for Cisco IP Communicator Release 7.0 - Using ...
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cipc/7_0/english/user/guide/CIPCUG70/ipcugdev.html
• If you install an audio device that requires device drivers (a USB handset, USB headset, or a sound card) after launching, Cisco IP Communicator does not recognize the device until you relaunch the application. The Audio Tuning Wizard automatically launches so that you can tune the device.
Now you know Cisco Ip Communicator No Audio Device
Now that you know Cisco Ip Communicator No Audio Device, we suggest that you familiarize yourself with information on similar questions.
