We have collected the most relevant information on Default Sink Pulseaudio. Open the URLs, which are collected below, and you will find all the info you are interested in.
Down the drain: The elusive ‘default’ PulseAudio sink ...
https://brokkr.net/2018/05/24/down-the-drain-the-elusive-default-pulseaudio-sink/#:~:text=There%20is%20no%20such%20thing%20as%20a%20default,%E2%80%9Cif%20the%20stream%20has%20not%20been%20seen%20before%E2%80%9D.
How to change pulseaudio sink with "pacmd set-default …
https://askubuntu.com/questions/71863/how-to-change-pulseaudio-sink-with-pacmd-set-default-sink-during-playback
PulseAudio pacmd is not capable of switching the default sinks while there is an actively playing stream to the sink input. However there is a way to still achieve this. Changing default sink from command line First we need to determine the index number of the sinks we want to switch. This can be done by calling: pacmd list-sinks
Down the drain: The elusive ‘default’ PulseAudio sink ...
https://brokkr.net/2018/05/24/down-the-drain-the-elusive-default-pulseaudio-sink/
There is no such thing as a default output device (or sink) in PulseAudio. It say so right there in the official documentation. There is something referred to as a fallback device which is used “if the stream has not been seen before”. Yet there is …
kubuntu - PulseAudio not using default sink - Unix & Linux ...
https://unix.stackexchange.com/questions/525070/pulseaudio-not-using-default-sink
Pulseaudio keeps a database for all applications which sink they were connected to, and on startup restores this connection instead of using the default sink. The default sink is only used for "new" applications. I don't know why your move-sink-input failed. Can you move it with pavucontrol? Edit. Looking at the github repository of MonoGame finds OpenAL code. …
PulseAudio/Examples - ArchWiki - Arch Linux
https://wiki.archlinux.org/title/PulseAudio/Examples
To route a particular client's output to it, find the client under the "Playback" tab, then change the client from its current sink (e.g. "Built-in Audio Analog Stereo") to "RTP". To use the RTP sink by default for all clients, add this to /etc/pulse/default.pa, then restart the local pulseaudio server: set-default-sink rtp ALSA monitor source
linux - Pulseaudio set/check default source - Stack Overflow
https://stackoverflow.com/questions/59150186/pulseaudio-set-check-default-source
default-sink = alsa_output.pci-0000_00_1b.0.hdmi-stereo default-source = alsa_input.pci-0000_00_1b.0.analog-stereo. 2.change /etc/pulse/default.pa, add following lines: ### Make some devices default set-default-source alsa_input.pci-0000_00_1b.0.analog-stereo. After configuration complete, I tried pulseaudio -D and reboot the device, but the config take no …
command line - Get active sink in PulseAudio - Unix ...
https://unix.stackexchange.com/questions/547899/get-active-sink-in-pulseaudio
When I connect a bluetooth speaker, that's what all audio goes through, nevertheless, sink 0 is still marked as default. When audio is playing, the sink that is outputting it displays 'state: RUNNING'. But once playback stops, that goes back to SUSPENDED. Is there any reliable way to find out what sink PulseAudio will use for audio?
audio - How to set up a PulseAudio sink? - Raspberry Pi ...
https://raspberrypi.stackexchange.com/questions/8621/how-to-set-up-a-pulseaudio-sink
load-module module-tunnel-sink sink_name=rpi_tunnel server=tcp:192.168.2.13:4713 sink=bcm1 If you don't put a sink_name in, pulseaudio won't start. The sink refers to the sink name on the pi side, which then also needs a name; add a corresponding sink_name to the module-alsa-sink line in default.pa there:
How correctly to switch pulseaudio's default sink ...
https://www.reddit.com/r/linuxaudio/comments/939wwz/how_correctly_to_switch_pulseaudios_default_sink/
How correctly to switch pulseaudio's default sink? I'm currently using sequence of pacmd set-card-profile pacmd set-default-sink pacmd move-sink-input to switch audio between headphones and hdmi. It works fine as long as everything is running. But fails to switch default output in this case: 1) chrome is running 2) switch audio to hdmi
PulseAudio - ArchWiki - Arch Linux
https://wiki.archlinux.org/title/PulseAudio
By default, PulseAudio is configured to automatically detect all sound cards and manage them. It takes control of all detected ALSA devices and redirects all audio streams to itself, making the PulseAudio daemon the central configuration point. The daemon should work mostly out of the box, only requiring a few minor tweaks.
Linux, PulseAudio, sync`source-output` and `default-sink ...
https://www.reddit.com/r/obs/comments/slhxgb/linux_pulseaudio_syncsourceoutput_and_defaultsink/
Linux, PulseAudio, sync`source-output` and `default-sink` so I will record the same sound that I hear
Now you know Default Sink Pulseaudio
Now that you know Default Sink Pulseaudio, we suggest that you familiarize yourself with information on similar questions.
