We have collected the most relevant information on Diyaudio Elsinore. Open the URLs, which are collected below, and you will find all the info you are interested in.
The "Elsinore Project" Thread | diyAudio
https://www.diyaudio.com/community/threads/the-elsinore-project-thread.97043/
The Veena is rated 89dB but the Elsinore was judged about 3dB more sensitive. This latest version is VERY easy to drive for a multi-way type speaker. The new Peerless HDS tweeter is, IMO, a real honey. I hope the DIY fraternity takes it to heart. It is quite an improvement on the Vifa XT25. If any of you guys are considering using it, go for it!
The "Elsinore Project" Thread | Page 232 | diyAudio
https://www.diyaudio.com/community/threads/the-elsinore-project-thread.97043/page-232
The Elsinores achieve this with extra Sd with 4 drive units per speaker. Another approach to get low distortion in the 300Hz to 2khz band (as mentioned in the Purifi article) is to go 3 way. Taking the Elsinores as an example, the top 2 …
The "Elsinore Project" Thread | Page 5 | diyAudio
https://www.diyaudio.com/community/threads/the-elsinore-project-thread.97043/page-5
As it is, the current series/parallel configuration of the Elsinores give you a nominal 8 Ohm load. If you parallel first before series, then you'd have to do a series crossover (Elsinores uses parallel crossover). I am afraid you are on your own and whatever you end up with, they won't be an Elsinore speaker. Joe R.
The "Elsinore Project" Thread | Page 230 | diyAudio
https://www.diyaudio.com/community/threads/the-elsinore-project-thread.97043/page-230
You might considered the Anarchy XBL motor 7-inch drivers. Price is $66USD each. They’ve been around a number of years and vendors, under somewhat varying model numbers for apparently the same driver, but don’t seem to be that well known. Current model numbers are Anarchy-704 (4-ohm), and Anarchy-708 (8-ohm).
The "Elsinore Project" Thread | Page 3 | diyAudio
https://www.diyaudio.com/community/threads/the-elsinore-project-thread.97043/page-3
The basic thing to remember is the tweeter needs to be as far away from the listener and the 5 1/4" PPB HDS driver closer. The rear cut-out - needs to match the dimensions of whatever terminals you use. The Tweeter must be flush mounted and 5 1/4" PPB driver not. Stuffing: I used wool/dacron (polyester) bats.
Elsinore Speakers DIY
https://customanalogue.com/elsinore/elsinore_index.htm
THE CROSSOVER - Elsinore Mk 6. NOTE: THERE ARE TWO VERSIONS. The SB17NRXC35-8 driver is now discontinued. The new drivers is SB17MFC35-8 and is the same driver except cone material mineral load polycone. The Crossover i the same with only two exception, values of L2 and R3 have been changed.
The diyAudio Store - DIY amplifier kits, chassis, and parts
https://diyaudiostore.com/
The circuit board is really well made and solders easily. Like all kits from the DIYAUDIO store, this is a terrific product, and I highly recommend it! Michael L. 01/24/2022 . B1 with Korg Triode (B1K) Full Kit . Whammy Circuit Board.
DCAudioDIY.com • View topic - Building Elsinore Speaker
http://www.dcaudiodiy.com/phpBB3/viewtopic.php?f=4&t=1443
DCAudioDIY.com • View topic - Building Elsinore Speaker. A place to discuss member's DIY audio projects & post pictures/schematics. NOTE: There is a limit of 2MB per attachment, and a maximum of 3 attachments per message. If you need to post more than 3 attachments, just add another message.
DIY Audio Projects Forum • Giveaway #2 - MyRefC LM3886 ...
https://diyaudioprojects.com/Forum/viewtopic.php?t=630
This prize rocks. It is two mono kits of the MyRefC LM3886 chipamp kits that Uriah and Peter recently put together (a very large effort - thanks guys) as part of a groupbuy. The chipamp design is by Mauro Penasa and it is well regarded (see the schematic at the bottom of post). Also included in the giveaway are two 160VA (120V primary, dual 24V ...
Review January 2009
http://www.customanalogue.com/elsinore/elsinore_23.htm
Dissecting the Elsinore means nothing anyway because they simply sound Fabulous but I will post much more thoughts and experiences on diy audio. I have a personal vendetta against some commercial brands and mainstream magazines based on some bad experiences, so my retaliation is to try to get people to believe/realize that the Elsinore easily ...
Now you know Diyaudio Elsinore
Now that you know Diyaudio Elsinore, we suggest that you familiarize yourself with information on similar questions.
