Gainclone Diyaudio.Com

Balanced Gainclone | diyAudio

https://www.diyaudio.com/community/threads/balanced-gainclone.13808/

The gain of the non-inverted amplifier is Av = 1+Rf/R1, and the gain of the inverted gainclone is Av = -Rf/R1. (R1 is the 10k in the picture, and Rfeedback is the 220k) This would mean that with the potentiometer at full signal, then the gain of the non-inverted would be 23, and the inverted would be -22. This issue could be fixed with a 230k ...

Gainclone Impedance | diyAudio

https://www.diyaudio.com/community/threads/gainclone-impedance.18136/

Featured Vendors The diyAudio Store Parts Connexion miniDSP DIY HiFi Supply. Members Market Swap Meet Group Buys. Vendors Market Vendor's Bazaar. ... What is the impedance of a gainclone and can it be raised to >50k if …

Gainclone LM3886 DC servo | diyAudio

https://www.diyaudio.com/community/threads/gainclone-lm3886-dc-servo.30670/

Göteborg, Sweden. sjostromaudio.com. 2004-03-24 8:14 am. #10. 2004-03-24 8:14 am. #10. The diodes is only there for fault conditions. The LM3886 is slower than the AD8620 therefore the AD8620 can track the LM3886. My opinion is still that these diodes are of minor importance in this particular application with used opamp.

Commercial Gainclone kit- building instructions | diyAudio

https://www.diyaudio.com/community/threads/commercial-gainclone-kit-building-instructions.123003/

Disclaimer: This Vendor's Forum is a paid-for commercial area. Unlike the rest of diyAudio, the Vendor has complete control of what may or may not be posted in this forum. If you wish to discuss technical matters outside the bounds of what is permitted by the Vendor, please use the non-commercial areas of diyAudio to do so.

DIY LM3886 Chip Amplifier (Gainclone) Kit

https://diyaudioprojects.com/Chip/LM3886_CA/LM3886_CA.htm

The SMPS-powered Gainclone – diyaudio.de

https://diyaudio.de/the-smps-powered-gainclone-2015/

The SMPS-powered Gainclone. 3. February 2021. 4. February 2021. Gainclone projects have been described extensively in the past and there is no point in repeating what is written elsewhere. The new aspect of this implementation is the power supply. I used the SMPS300RE Power supply Module 300W +/-30V for my Gainclone.

Gainclone Integrated Amplifier - Jeremy Young Design

https://jeremyyoungdesign.com/2020/10/26/gainclone-integrated-amplifier/

I purchased the Audiosector Gainclone LM3875 PCB + component kit about four years ago, it sat under my desk gathering dust until this year, when I finally decided to put it to use.. The Gainclone concept is based on the original Kimura-San/47Labs Gaincard design, which takes a “less-is-more” approach, low component count, extremely short signal path etc. at the …

LM3875 Gainclone - Building Instructions - Audiosector

https://www.audiosector.com/wp-content/uploads/2019/01/LM3875-kit-instructions.pdf

LM3875 Gainclone - Building Instructions Page 3 Identifying resistor values should not be a problem, as there are 4pcs that are 22k, 2 resistors are always longer, those would be 680R and the other two are 220R.

DIY Chip Amps, Gainclone, Op-amp and T-Amp Projects

http://www.diyaudioprojects.com/Chip/chip.htm

Nanoo LM3875 Gainclone Chip Amplifier - 18 December 2006 Another Gainclone amplifier! This is Mark's tiny Nanoo Amplifier. The enclosure is an aluminum box that measures only 119 X 94 X 34 mm. The amplifier uses the popular LM3875 IC chip with point-to-point wiring construction. Power to the amplifier is provided via an external power supply.

Modulus-86 Gainclone - Solid State - diyAudio.rs

https://www.diyaudio.rs/topic/9144-modulus-86-gainclone/

Modulus-86 Gainclone Modulus-86 Gainclone. Od Muad'Dib , Septembar 18, 2018 in Solid State. Share More sharing options... Pratilaca 1. Preporučeni Komentari. ... Potrebno je da budeš član DiyAudio.rs-a da bi ostavio komentar. Kreiraj nalog. Prijavite se za novi nalog na DiyAudio.rs zajednici. Jednostavno je! Registruj novi nalog. Prijavi se.