We have collected the most relevant information on High Power Audio Output Transistors. Open the URLs, which are collected below, and you will find all the info you are interested in.
Favorite High Power Output Transistor | diyAudio
https://www.diyaudio.com/community/threads/favorite-high-power-output-transistor.37670/
MJ802 & MJ4502 or (ECG181 & ECG180) type TO-3 are good linear High current devices for driving a lower output Z...like 4Ohms. They only have 100V breakdown voltage, but for higher current, you will have lower voltage than with 8Ohms. OHM's LAW The beta is lower though so your drivers have to be larger... so what, big deal. M millwood
Audio Transistors - ON Semiconductor
https://www.onsemi.com/products/discrete-power-modules/audio-transistors
onsemi supplies audio transistors for high power audio circuits.
Best sounding transistors - High-End Audio Discussion Forum
https://forum.audiogon.com/discussions/best-sounding-transistors
While using a large number of output transistors reduces the load on each transistor, the downside is that a large number of transistors create a high capacitance load for the driver stages, slowing down the amplifier. This high capacitance reduces the slew rate and can create TIM distortion.
Favorite High Power Output Transistor | Page 18 | diyAudio
https://www.diyaudio.com/community/threads/favorite-high-power-output-transistor.37670/page-18
Favorite High Power Output Transistor. ... I would like to know what your favorite high power audio output transistors are. This would be a replacement for 2N3055. I would be looking for at least as much Current and Power capability with improved linearity before feedback.
Output Transistors In Transistors for sale | eBay
https://www.ebay.com/b/Output-Transistors-In-Transistors/4666/bn_7022147050
Best transistor to use for audio amplifier - Electrical ...
https://electronics.stackexchange.com/questions/97827/best-transistor-to-use-for-audio-amplifier
You can only drive the output transistors with a signal that is restricted to the power rails and if this is (say) 24V dc - you should be able to drive a signal that is 22Vp-p to the power transistors. Given that each BJT would "lose" 0.7 volts (because of the base emitter junction), the maximum output voltage will be about 20.6 volts peak to peak.
Output Transistors also used in which other Stereo ...
http://www.oaktreevintage.com/resources_misc/output_transistors_in_stereo_amps_receivers_substitutions_also_used_in....htm
Matching Power and Driver Transistors - The Audio Pages ...
https://sound-au.com/transistor-matching.htm
If you want to use a quiescent current of 100mA, the voltage across the resistor will be 10 x 0.1 = 1V. Remember to divide the total quiescent current by the number of parallel output devices first. For power transistors, the 'Base Current Range' switch (SW5) needs to be set to the high range (100 Ohms), and base current is limited to about 60mA.
Transistors - Output Transistor - Trout Underground
https://troutunderground.com/Transistors-Output-Transistor/
The set of eight (x8) genuine Japan-made NEC low noise audio power output transistor for quality high-end 100-125 Watts stereo power amplifier project as pictured. They're in very good working condition ( tested) The set is four (x4) PNP 2SB541 and four (x4) NPN 2SD388.
300 Watts Output High Power Audio Amplifier
https://www.eeweb.com/300-watts-output-high-power-audio-amplifier/
MJ15003 – a ballasted epitaxial-base silicon NPN high power transistor used for series and shunt regulators, solenoid drivers, power switching circuits, high-fidelity amplifiers, and other industrial and commercial use due to its features such as high gain at high current, maximum safe-area-of-operation curves, low saturation voltages, rugged design, and high …
Now you know High Power Audio Output Transistors
Now that you know High Power Audio Output Transistors, we suggest that you familiarize yourself with information on similar questions.
