We have collected the most relevant information on Input Audio Multiplexer. Open the URLs, which are collected below, and you will find all the info you are interested in.


Input Multiplexer - Open Sound

    http://www.opensound.com/imux.html#:~:text=Input%20Multiplexer%20%28IMUX%29%20Introduction%20IMUX%20is%20a%20virtual,the%20input%20source%20%28via%20mic%2C%20line%20or%20CD%29.
    none

Input Multiplexer - Open Sound

    http://www.opensound.com/imux.html
    Input Multiplexer (IMUX) Introduction. IMUX is a virtual recording engine that permits up to 8 audio recording applications to run at the same time. Generally most soundcards permit only a single recording application to record the input source (via mic, line or CD). With IMUX,you can use up to 8 recording applications to record the same source in different sample rates, …

Audio Switches and Multiplexers - Maxim Integrated

    https://www.maximintegrated.com/en/products/analog/analog-switches-multiplexers/audio.html
    Maxim offers the industry's broadest selection of low-on-resistance (low R ON) analog switches and multiplexers for high-fidelity, portable audio applications. All Audio Switches and Multiplexers. Technical Documentation.

Escape Cable Hell With An Audio I/O Multiplexer | Hackaday

    https://hackaday.com/2015/11/02/escape-cable-hell-with-a-multi-io-audio-multiplexer/
    If you ever find yourself swapping between a mix of audio inputs and outputs and get tired of plugging cables all the time, check out …

switches - Multiplexer not switching any audio input ...

    https://electronics.stackexchange.com/questions/360396/multiplexer-not-switching-any-audio-input
    The most obvious thing I see is that your mux inputs are not ground-referenced. That is, you should have a largish resistor to ground on each analog mux input. If you don't, there is no way to control the "resting" level of the inputs. Try something like 100k. Second, tie your floating R and S inputs on IC6 to ground.

Home made audio multiplexer (switch) using 4051 or 4052 ...

    https://www.diyaudio.com/community/threads/home-made-audio-multiplexer-switch-using-4051-or-4052-74hc.141262/
    The dual 4:1 version would be more useful, the ADG509F, since one chip is all you need for a stereo four-input switch. Maxim's versions are the MAX4708 and MAX4709, if those are more available. Just beware of chips from vendors in China that are used non-faultprotected MUX chips that have been removed from boards and re-marked.

Digital Circuits - Multiplexers - Tutorialspoint

    https://www.tutorialspoint.com/digital_circuits/digital_circuits_multiplexers.htm
    Multiplexer is a combinational circuit that has maximum of 2 n data inputs, ‘n’ selection lines and single output line. One of these data inputs will be connected to the output based on the values of selection lines. Since there are ‘n’ selection lines, there …

Multiplexer and Demultiplexer - idc-online.com

    https://www.idc-online.com/technical_references/pdfs/electronic_engineering/Multiplexer%20and%20Demultiplexer.pdf
    The 4-to-1 multiplexer has 4 input bit, 2 control bits, and 1 output bit. The four input bits are D0,D1,D2 and D3. only one of this is transmitted to the output y. The output depends on the value of AB which is the control input. The control input determines which of the input data bit is transmitted to the output.

Audio MUX IC - All About Circuits

    https://forum.allaboutcircuits.com/threads/audio-mux-ic.9066/
    The most common analog mux (there are a lot) I could find was a 4051. However since this will only be used for audio signals I was hoping that somebody could point me to an analog mux that is optimised for audio signals. Cost is not a factor as this project would most likely be built once. Thanks.

Multiplexer block - Fractal Audio Wiki

    https://wiki.fractalaudio.com/axefx2/index.php?title=Multiplexer_block
    The Multiplexer block (MUX) is a routing and switching tool. It allows on-the-fly switching between either rows on the grid (as long as you have them connected), or physical inputs (Input blocks on the grid aren't required), or USB. Or you can use its Bypass to switch between just two things. Note that only one input can be active at a time.

Arduino Analog I/O Multiplexer - Hackaday

    https://hackaday.com/2018/06/09/arduino-analog-i-o-multiplexer/
    Arduino Analog I/O Multiplexer. [SeanHodgins] has a project in mind where he needs to sample over 500 analog sensors. To get ready, he made a breakout board for 32-channel analog multiplexer ...

Now you know Input Audio Multiplexer

Now that you know Input Audio Multiplexer, we suggest that you familiarize yourself with information on similar questions.