We have collected the most relevant information on Ip Communicator No Audio Device. Open the URLs, which are collected below, and you will find all the info you are interested in.
IP Communicator Error Message: There are No Compatible ...
https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/ip-communicator/107347-IP-communicator.html#:~:text=Problem%20When%20you%20installed%20the%20IP%20Communicator%20on,no%20compatible%20sound%20devices%20installed%20on%20this%20computer.
IP Communicator Error Message: There are No …
https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/ip-communicator/107347-IP-communicator.html
Solved: Cisco IP Communicator - No Devices Detected ...
https://community.cisco.com/t5/ip-telephony-and-phones/cisco-ip-communicator-no-devices-detected/td-p/2073804
It will allow you to click on "cancel" when IP Comm says the "default" device is not found and start the audio wizard and then your device will be listed there. For instance, using this method allows you to use headsets, integrated speakers/mic on a laptop, or whatever you like. Regards 5 Helpful Reply moman62 Beginner
No sound output with IP Communicator - Cisco Community
https://community.cisco.com/t5/ip-telephony-and-phones/no-sound-output-with-ip-communicator/td-p/1851752
If yes, ensure you are selecting the interface which you get after connecting over VPN & not the default NIC. This is usually the main cause of one-way audio. Also, ensure CIPC installation on Win 7 is supported, mostly it is but double chk to be sure. If it helps, pls rate the post.
Cisco IP Communicator - Audio Issues - TeamDynamix
https://volstate.teamdynamix.com/TDClient/1994/Portal/KB/ArticleDet?ID=111924
Right click on the device, then click on "Set as Default Device". Then click "OK" or "Apply" to save the settings. Step 2: Adjusting Audio Settings Within CIPC Run Cisco IP Communicator and locate the Preferences button (circled in red). Click on Audio Tuning Wizard. Set all of these individual categories as Default Windows Audio Device.
Cisco Bug: CSCsa65866 - Communicator-'No Compatible Sound ...
https://quickview.cloudapps.cisco.com/quickview/bug/CSCsa65866
Symptom: IP Communicator Audio Tuning Wizard shows nothing in the dropdown selection boxes, and when Communicator is launched, it gives a messages stating: "There are no compatible sound devices installed on this computer."Conditions: Attempting to install/use IP Communicator on a system that has different names for the Playback (wave out) and …
Troubleshooting Cisco IP Communicator
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cipc/7_0/english/user/guide/CIPCUG70/ipcugts.pdf
† Installing Audio Devices Before First Launch, page 1-3 † How to Assign Audio Modes, page 4-9 † Selecting an Audio Mode, page 4-9 † Removing and Re-Installing Audio Devices, page 5-6 Problem After launching, Cisco IP Communicator shows no extension number or the wrong extension number. Solution Contact you system administrator for ...
Solved: Problem with audio in Cisco IP Communicator ...
https://communities.vmware.com/t5/Horizon-Desktops-and-Apps/Problem-with-audio-in-Cisco-IP-Communicator/td-p/2109623
Upgrade your Windows VM Audio driver to Teradici's audio driver; Point Control Panel -> Sounds to use Teradici audio as default and it should be OK. Works on Windows 7 x 64 with View 5.0.1. Cisco IP Communicator version 8.6.1
No Audio Cisco IP Communicator ver 8.6.6.0 - reddit
https://www.reddit.com/r/Cisco/comments/nq39pj/no_audio_cisco_ip_communicator_ver_8660/
Hello, I am using Cisco IP Communicator ver 8.6.6.0 and can get dial tone, the phone rings and connects, but I cannot hear the other person and the other person cannot hear me. I am using in conjunction with a FortiClient VPN. This has been tested on multiple recipients, the client has been uninstalled and reinstalled cleanly, PC and drivers all updated, network settings have been …
Cisco IP Communicator on Virtual Machine? - UC Collabing
https://www.uccollabing.com/cisco-ip-communicator-on-virtual-machine/
On your System > Go to Run > Type “mstsc” Enter the IP Address of Microsoft Windows Click Show Options Click on Local Resources Tab Click on Remote Audio Settings Remote Audio Playback > Radio Check “Play on Remote Computer” Click on OK and Click on Connect Right Click on Cisco IP Communicator and “Run as Administrator”
Cisco IP Communicator default windows audio - Spiceworks
https://community.spiceworks.com/topic/2222636-cisco-ip-communicator-default-windows-audio
Swapped out the headset, and now the IP Communicator only sees default windows audio from any of the dropdowns. I uninstalled the application, restarted, and reinstalled the application. Same issue. I had him unplug the new headset and plug it directly into the computer, since he's using a dock. Same issue with the IP Communicator.
Now you know Ip Communicator No Audio Device
Now that you know Ip Communicator No Audio Device, we suggest that you familiarize yourself with information on similar questions.
