We have collected the most relevant information on Non Inductive Resistors Audio. Open the URLs, which are collected below, and you will find all the info you are interested in.
Non-Inductive Resistors | diyAudio
https://www.diyaudio.com/community/threads/non-inductive-resistors.625/
Non-inductive 5watt resistors in a ceramic pack can be sourced from RS Components (I think they are from Megitt, but can't quite remember). Yes, I made the 1KW amplifier from Elektor. I faced some problems with the powersupply to the input section where the 7808 and 7908 regulators have been lifted to 80volts using zeners.
RadioShack 8-ohm Non-inductive Resistor 20 Watt for …
https://www.amazon.com/8-ohm-Non-inductive-Resistor-Audio-Applications/dp/B0058E98R4
RadioShack 8-ohm Non-inductive Resistor 20 Watt for Audio Applications Visit the RadioShack Store 26 ratings $4 49 Use this device for protection and current control in your electronics The 8-Ohm Resistor is rated 20 watts (5% tolerance) Helpful in high-power audio connections and projects Compare with similar items Product Description
Non-Inductive Resistors - 0 Ohm to 700 Ohm
https://www.surplussales.com/Resistors/NonInductive/Res-NonInd_list.htm
Non-Inductive Termination Resistor 100 Ohm / 225 Watt (RNI) FR200-100-NI Memcor Non-Inductive Termination Resistor. Tubular style with tabbed terminals. 100 ohm, 225 watt. 1-1/4" diameter x 10-1/2" long. Use for in-series / parallel for different wattages and resistance values. Type E. Used in Gates / Harris equipment. $49 each - $43 (10+)
Top 10 Best Resistors For Audio Based On Scores - Best ...
https://bestbeddinginfo.com/best-resistors-for-audio/
Because We have worked hard studying and analyzing 55201 reviews for Resistors For Audio and rating them. It was a difficult job to list only ten products for Resistors For Audio where thousands of them available online. I hope it will help you to take final decision for Best Resistors For Audio. ... RadioShack 8-ohm Non-inductive Resistor 20 ...
"Non Inductive" resistors. - High-End Audio Discussion Forum
https://forum.audiogon.com/discussions/quot-non-inductive-quot-resistors
If you wanted to be sure you could get some 8 ohm non-inductive power resistors at Radio Shack for $2.29 each and have your two 4 ohm pads for under $10. eldartford OP 4,262 posts 10-15-2004 7:08pm Herman...Two of those in parallel (for 4 …
inductive versus non-inductive resistors as loads for ...
https://eevblog.com/forum/projects/inductive-versus-non-inductive-resistors-as-loads-for-audio-amplifiers/
Re: inductive versus non-inductive resistors as loads for audio amplifiers. Regardless of the need or not for a purely resistive load, it's pretty trivial to compensate an inductive R with a series R-C in parallel. 8 ohm resistive load with 10uH of inductance. fc = R / (2.pi.L) = 8 / (2.pi.10uH) = 127.324 kHz.
Non-Inductive Resistors | Surplus Power Resistors
https://www.electronicsurplus.com/resistors/non-inductive-resistor
Ohmite- Kanthal Global - CESIWID - 890SP501K Ceramic Tubular Resistor - Non Inductive. 800 Series Type Type SP Tubular High Voltage Power Resistor for great A-C power handling capability, whether it be at power frequency or many megahertz. High-Power / Non-Inductive - High Voltage. Resistance: 500 Ohm +/- 10%. Power: 375 Watt. Maximum Voltage: 16KV.
Mills Resistors, Sonic Craft
http://www.soniccraft.com/index.php/resistors-mills-c-29_53
High quality audiophile & DIY audio resistors - 5 watt, 10 watt, and 12 watt Mills "MRA". Values from 0.1 ohm to 100K ohm. Non-magnetic, non-inductive.
Do Mills resistors REALLY sound different? - Techtalk ...
https://techtalk.parts-express.com/forum/tech-talk-forum/28056-do-mills-resistors-really-sound-different
mills are non inductive so with a tweeter they may sound better then an inductive resister that was used and the mH was not accounted for.. if a low cost non inductive was used it would be hard to tell them apart. i think a lot of times people may have end an …
Is it audible? - Audio Science Review (ASR) Forum
https://www.audiosciencereview.com/forum/index.php?threads/replace-resistor-by-low-inductance-resistor-is-it-audible.12162/
I normally use the non-inductive resistors in tweeter circuits but more for a tighter tolerance rating than the slight difference in inductance. The encapsulation can affect the cost as some resistors are made for more demanding environments; however, this isn't an issue / advantage in a home audio speaker.
Now you know Non Inductive Resistors Audio
Now that you know Non Inductive Resistors Audio, we suggest that you familiarize yourself with information on similar questions.
