We have collected the most relevant information on Polk Audio Crossover Settings. Open the URLs, which are collected below, and you will find all the info you are interested in.
crossover setting??? — Polk Audio Forum
https://forum.polkaudio.com/discussion/121536/crossover-setting#:~:text=-%20Set%20the%20receiver%27s%20crossover%20to%20150%20Hz,am%20guessing%20120%20Hz%20will%20sound%20the%20best%29
Crossover Settings — Polk Audio Forum
https://forum.polkaudio.com/discussion/193162/crossover-settings
Just like Jaydog mentioned, set all speakers to small with crossover point between 80hz to 100hz. Subwoofer though should be set to 'LFE' (not LFE+Main) and left at default 120hz. If you are getting better performance setting the speaker crossover below 80hz, you are having issues that need to be looked into and resolved.
Crossover settings — Polk Audio Forum
https://forum.polkaudio.com/discussion/192318/crossover-settings
properly set up and calibrated, the 80ish crossover setting is a good thing and will actually give you better overall performance, dynamics, and power handling. Let the main speakers focus on the frequency range they are designed to and not stress trying to play low bass thats supposed to be handled by the sub anyway.
Crossover settings. — Polk Audio Forum
https://forum.polkaudio.com/discussion/187084/crossover-settings
My receiver has settings to set a crossover point for each individual channel. The sub also has the knob on the back to set crossover. What do you do with the knob if you want to set different frequencies for different channels ? Is that not used ? I'll be plugging it into the pre out subwoofer jack on the reciever. Bought a Polk Audio HTS 12.
Crossover settings — Polk Audio Forum
https://forum.polkaudio.com/discussion/118505/crossover-settings
Polk Audio RM8 satellite x4 Wired direct to AVR w/14gauge. Polk Audio RM8 center x1 Wired direct to AVR w/14gauge. JBL 200wt Sub wired LFE. Traditional 5.1 surround sound layout configuration. 2 front wall mounted 8 ft from floor. center in front of tv. 2 rear wall mounted approx 6ft off the floor. Sub in rt front corner of the room.
Crossover Settings — Polk Audio Forum
https://forum.polkaudio.com/discussion/84523/crossover-settings
subwoofer - polk psw-10. these are the settings available, under the speaker settings there is a crossover setting, right now it's at 100Hz. then there is a "center geq" which has all kinds of frequency settings. then there is an lfe level with some settings for sp lfe and hp lfe which both are set at 0. then there is something for dynamic range with settings for sp and hp min, std, or …
crossover setting??? — Polk Audio Forum
https://forum.polkaudio.com/discussion/121536/crossover-setting
The crossover is marked low and high out , the low being the sub the high being my mains (satalittes) I run the subs at 80 hertz and down and the mains at 70 hertz and up . The crossover has a very steep slope so when its set at 80 hertz it IS 80 hertz I get nothing above that its just very clean pure sub without any upper bass (thats like 100 hz bass) .
PSW 505 crossover settings — Polk Audio Forum
https://forum.polkaudio.com/discussion/93803/psw-505-crossover-settings
The crossover on the PSW-505 only works if you use the red and white RCA input.If you use the LFE input the crossover on the sub does not work because your reciever it what would set the crossover.you should be able to hear the difference between 60hz and 120hz unless you have your reciever set to a low crossover point.
Crossover settings Polk | Tom's Guide Forum
https://forums.tomsguide.com/threads/crossover-settings-polk.325476/
In a small room you will get more control of the bass with the sub. The crossover frequency is more complicated. I would say 80hz should be fine. You can try a lower frequency say 50hz but will...
Crossover settings... help! | AVS Forum
https://www.avsforum.com/threads/crossover-settings-help.3025542/
1. It seems you are limited somewhat by amplifier headroom. You can free up a little more by raising the crossovers a... 2. Turn the Low Pass dial on the subs to 120 Hz. This will "cascade" the Low Pass of the receiver and the Low Pass of... 3. Try plugging the ports of the subs. This may raise ...
polkaudio PSW10/ PSW12 Powered Subwoofers Owner's Manual ...
https://manuals.plus/polkaudio/polkaudio-psw10-psw12-powered-subwoofers-owner-s-manual
Now listen carefully for the point at which the subwoofer transitions to your main speakers. This is the crossover point, and this point should be below the frequency of a male human voice. Whichever phase setting sounds louder or fuller at the subwoofer’s crossover (transition) point is the optimum setting. Sometimes no difference will be heard.
Now you know Polk Audio Crossover Settings
Now that you know Polk Audio Crossover Settings, we suggest that you familiarize yourself with information on similar questions.
