We have collected the most relevant information on Polk Audio Psw1000 Fuse. Open the URLs, which are collected below, and you will find all the info you are interested in.
PSW1000 . fuse keeps blowing. — Polk Audio Forum
https://forum.polkaudio.com/discussion/164093/psw1000-fuse-keeps-blowing
PSW1000 . fuse keeps blowing. So last week I realize my subwoofer was unplug, so I plugged it in. the switch was on the on position and once I plug it in I got a pop noise. So I pull the fuse see that it blew so I went to radioshack. I got 5amp 250volt slow blow as I dont have a manual and didnt think about the forums until yesterday.
PSW SERIES - Polk Audio
http://web.polkaudio.com/downloads/manual/PSW250_350_450_MN.pdf
Matthew S. Polk Chairman and Co-Founder P.S.: A wealth of information can also be found on our award-winning web site: www.polkaudio.com. POLK AUDIO— A HISTORY OF EXCELLENCE Polk Audio was founded in 1972 by Matthew Polk and George Klopfer. Their dream was to make speakers with the performance of the world’s best speakers, at reasonable prices.
fuses — Polk Audio Forum
https://forum.polkaudio.com/discussion/8071/fuses
dholmes, Yes, if your Polk is an 8-ohm, 250w speaker, a 2-amp fuse is right (actual answer is 1.98 amp, but rounding off is fine). If it were a 4-ohm, you d want a 4-amp fuse. Side Note 1: To produce the same power the current demand rises as the speaker impedance falls. This is why you often read in the Club about the need for high-current amps.
PSW10 - Blown Fuse — Polk Audio Forum
https://forum.polkaudio.com/discussion/76980/psw10-blown-fuse
All was fine until a power surge (possible lightning) blew out all of my networking equipment as well as my Polk PSW10 which was on the same line. I opened the back and replaced the 2 amp, 250v fuse (which was blown) with a 2.5 amp,250v fuse which was all I had on hand. The new fuse blew immediately after the speaker hummed.
PSW108 Blowing Fuses and Not Turning On — Polk Audio Forum
https://forum.polkaudio.com/discussion/190722/psw108-blowing-fuses-and-not-turning-on
Contacted Polk and ran their driver/amp test- my driver is fine which means the amp is bad. Cool. Obviously I'm out of warranty and that doesn't bug me. They offered to let me ship it in for a diagnosis and repair cost but I'm already 99% sure whatever …
Polk Audio PSW1000 (Cherry) Powered subwoofer at …
https://www.crutchfield.com/ISEO-rmsbcspd/p_107PSW1KC/Polk-Audio-PSW1000-Cherry.html
Add depth to your music and serious impact to your home theater experience with the PSW1000 subwoofer from Polk. With a hard-hitting 400-watt amplifier and two 10" woofers, this high-performance sub moves a lot of air for deep bass you can feel. And Polk's exclusive PowerPort® technology reinforces the bass without adding audible distortion.
My PolkAudio PSW10 immediately blows its fuse upon plug-in ...
https://www.justanswer.com/electronics/69f6u-polkaudio-psw10-immediately-blows-its-fuse-upon-plug-in.html
My PolkAudio PSW10 immediately blows its fuse upon plug-in to 120V even when the Power switch is 'Off' and there is no audio in present. There are 2 (Power supply?) 4700 ufd electrolytics on the right edge of the PC board. the one closest to the rectifier shows 4.0 Ohms both ways while the other one shows 6.8 Ohms both ways.
Project #2 - Polk Audio Subwoofer Repair - YouTube
https://www.youtube.com/watch?v=QOxdwpGlcvw
In this video, I demonstrate how to replace the amplifier module in a Polk Audio subwoofer.
Amazon.com: Polk Audio PSW1000 Powered Subwoofer (Single ...
https://www.amazon.com/Polk-Audio-PSW1000-Powered-Subwoofer/dp/B000C8WK1W
One of the most advanced Polk Audio Powered Subwoofer, specifically engineered to deliver bass with the accuracy and depth demanded by the performance of the PSW Series. The PSW1000 features dual 10” long throw drivers mounted on massive 1”-think MDF baffles in a beautifully sculpted cabinet of high gloss black and real wood veneer.
Amazon.com: Polk Audio PSW1000 Powered Subwoofer (Single ...
https://www.amazon.com/Polk-Audio-PSW1000-Powered-Subwoofer/dp/B000QA3268
One of the most advanced Polk Audio Powered Subwoofer, specifically engineered to deliver bass with the accuracy and depth demanded by the performance of the PSW Series. The PSW1000 features dual 10” long throw drivers mounted on massive 1”-think MDF baffles in a beautifully sculpted cabinet of high gloss black and real wood veneer.
Now you know Polk Audio Psw1000 Fuse
Now that you know Polk Audio Psw1000 Fuse, we suggest that you familiarize yourself with information on similar questions.
