We have collected the most relevant information on Pulseaudio Asound Conf. Open the URLs, which are collected below, and you will find all the info you are interested in.
PulseAudio/Examples - ArchWiki - Arch Linux
https://wiki.archlinux.org/title/PulseAudio/Examples
Since pulseaudio-alsa contains only a configuration file /etc/asound.conf, if it is installed as dependency, one could simply comment all contents in /etc/asound.conf. alsamixer functions properly as well as any other ALSA clients. Also make sure common frameworks like Xine, Gstreamer and Phonon are configured to use ALSA: by default if they ...
PulseAudio has no sound, only has Dummy Output - Ask …
https://askubuntu.com/questions/1359038/pulseaudio-has-no-sound-only-has-dummy-output
To modify the configuration file. sudo gedit /etc/asound.conf. The above command will also open the file. Of course, add the following lines with your card and device number replacements. defaults.pcm.card 1 defaults.pcm.device 0. Save the file and restart your computer, and you will hear the sound.
[Solved] Need help with .asoundrc / PulseAudio ...
https://bbs.archlinux.org/viewtopic.php?id=184445
Delete ~/.asoundrc, install pulseaudio-alsa, which installs /etc/asound.conf, and read the pulseaudio wiki for further setup steps. I do not use pa any more, so I can help little with it. You should consider using modprobe to set your default device, which pulseaudio should also …
How-To: Pulseaudio - Debian User Forums
https://forums.debian.net/viewtopic.php?t=12497
For me only asound.conf works but it may be different for other people especially if you are not on debian. 4.Try a restart. 5.Try the commands "sudo dpkg-reconfigure pulseaudio" and "sudo dpkg-reconfigure pulseaudio-utils" to set things back to default. 6.Try a different device as stated in the Tinkering section.
PerfectSetup - freedesktop.org
https://www.freedesktop.org/wiki/Software/PulseAudio/Documentation/User/PerfectSetup/
The PulseAudio plugin for ALSA supports audio playback, audio capturing and supports the mixer. Preferred asound.conf: Depending on your system, using the '!' (exclamation point syntax) inside of an asound.conf or .asoundrc could have adverse effects, because it overwrites the system's ALSA configuration (often found in /usr/share/alsa/alsa ...
sound - Setting the default ALSA device for Pulseaudio ...
https://askubuntu.com/questions/294512/setting-the-default-alsa-device-for-pulseaudio
Answering the two questions: You can select the default device in PulseAudio with a GUI like the GNOME volume control, pavucontrol, or from the command line using pacmd set-default-sink.. By default, PulseAudio opens devices for 44.1 kHz or 48 kHz, whichever leads to lower resampling effort (so 96 kHz audio would usually lead to the device being opened at 48 kHz.
audio - How to get PulseAudio running? - Raspberry Pi ...
https://raspberrypi.stackexchange.com/questions/639/how-to-get-pulseaudio-running
Install pulseaudio and make sure user (e.g. eric) is part of the audio group: sudo apt-get install pulseaudio pulseaudio-utils sudo adduser eric audio Change /etc/asound.conf look like the following. This sets up pulseaudio to be used as an alsa device by default so applications use it without any additional configuration.
Setting up config for alsa at /etc/asound.conf - Raspberry ...
https://raspberrypi.stackexchange.com/questions/95193/setting-up-config-for-alsa-at-etc-asound-conf
Find your desired card with: cat /proc/asound/cards. and then create /etc/asound.conf with following: defaults.pcm.card 1 defaults.ctl.card 1. Replace "1" with number of your card determined above. If you are using PulseAudio, you should select the default there. Share. Improve this answer.
Use pulseaudio as bluetooth speaker on archlinux · GitHub
https://gist.github.com/yejun/2c1a070a839b3a7b146ede8a998b5495
Add file /etc/pulse/client.conf. default-server = /var/run/pulse/native autospawn = no Enable and start pulseaudio. sudo systemctl enable pulseaudio sudo systemctl start pulseaudio Config alsa if necessay, here is my /etc/asound.conf. pcm.!default { type plug slave { pcm "hw:0,0" } } ctl.!default { type hw card 0 }
Now you know Pulseaudio Asound Conf
Now that you know Pulseaudio Asound Conf, we suggest that you familiarize yourself with information on similar questions.
