We have collected the most relevant information on Pulseaudio Bit Perfect. Open the URLs, which are collected below, and you will find all the info you are interested in.
pulseaudio bit-perfect | Headphone Reviews and Discussion ...
https://www.head-fi.org/threads/pulseaudio-bit-perfect.443807/
Hi Is pulseaudio bit-perfect?Can i turn off resampling in pulse? Regards
Is this "bit perfect"* audio with pulseaudio? - Linux Mint ...
https://forums.linuxmint.com/viewtopic.php?t=347359
Re: Is this "bit perfect"* audio with pulseaudio? Post by rene » Thu Apr 15, 2021 6:06 pm By bitperfect audio is in fact normally meant a fully digital chain delivering the exact same bits at its destination as went into it at its source, whereas you are (supposedly I should say) talking about a regular sound card, not so much any digital ...
PulseAudio - Official Kodi Wiki
https://kodi.wiki/view/PulseAudio
PulseAudio can be run in one of two modes these are: Passthrough Mode Used if you want to passthrough (bitstream) AC3, DTS, and EAC3 to an AVR or other device. In order to allow passthrough to work with PulseAudio then it MUST be set to use a 2.0 channel configuration, despite the 2.0 setting this will still allow 5.1 audio from AC3, DTS, and EAC3.
Is it possible to achieve bit-perfect audio on Linux ...
https://unix.stackexchange.com/questions/319967/is-it-possible-to-achieve-bit-perfect-audio-on-linux
Pulseaudio is the mixer most Linux distributions use, and it likes to resample and mix the audio from multiple sources (leading to non-bit-perfect audio). If you'd looked a bit harder, you'd found guides on how to set this up, for example here .
sound - Pros/cons of running PulseAudio at 24 Bits to ...
https://askubuntu.com/questions/868842/pros-cons-of-running-pulseaudio-at-24-bits-to-match-hardware
The sound card runs at 24-bit/192KHz natively, and while I can edit asound.conf to make it run at other sampling rates, only 24-bit depth is supported (not 16). I understand that by default both ALSA and PulseAudio will downsample audio material to 16-bits/48KHz. I can edit the config files of each so that they run at 24-bit/48KHz instead.
BEGINNER QUESTION : Getting "BitPerfect" output in …
https://www.audiosciencereview.com/forum/index.php?threads/beginner-question-getting-bitperfect-output-in-linux.10549/page-5
While PulseAudio will likely never technically be able to be configured to be bit perfect, it will likely be quite a deal more convenient than most other alternatives for awhile longer. Especially is the case when dealing with multiple streams of different sample rates, when you don't feel like messing with a new distro install too much, etc.
UD-503 mpd alsa config bit perfect - Guillaume's playground
https://guillaumeplayground.net/ud-503-mpd-alsa-config-bit-perfect/
UD-503 mpd alsa config bit perfect. First of all, kill pulseaudio, burn it, it is useless for pure audio playback. Everything else, like kodi, with a hdmi audio output for example, will still work. Now you have a clean straight mpd -> alsa. You …
Audiophile – PulseAudio
https://www.freedesktop.org/wiki/Software/PulseAudio/Documentation/User/Audiophile/
By default, PulseAudio (PA) uses very conservative settings. This will work fine for most audio media as you will most likely have 44,100Hz sample rate files. However, if you have higher sample rate recordings it is recommended that you increase the sample rate that PA uses. In /etc/pulse/daemon.conf add: default-sample-format = s32le default-sample-rate = 96000.
Now you know Pulseaudio Bit Perfect
Now that you know Pulseaudio Bit Perfect, we suggest that you familiarize yourself with information on similar questions.
