We have collected the most relevant information on Pulseaudio Daemon 3.0. Open the URLs, which are collected below, and you will find all the info you are interested in.
PulseAudio 3.0 released [LWN.net]
https://lwn.net/Articles/529605/
Version 3.0 of the PulseAudio subsystem is out; see the release notes for details. "The tl;dr version for the lazy is: easier setup when your device is a Bluetooth source, some ARM NEON optimisations, configurable latency offsets, ALSA UCM [use-case manager] support for embedded folks, and a _lot_ of other fixes and infrastructure changes."
Running PulseAudio as System-Wide Daemon – PulseAudio
https://www.freedesktop.org/wiki/Software/PulseAudio/Documentation/User/SystemWide/
Running PulseAudio as System-Wide Daemon. Starting with PulseAudio 0.9.3 the daemon can be run as a system-wide instance which than can be shared by multiple local users. We recommend running the PulseAudio daemon per-user, just like the traditional ESD sound daemon. In some situations however, such as embedded systems where no real notion of a ...
PulseAudio Is Streaming With An Excessive Latency.
https://centosfaq.org/centos/pulseaudio-is-streaming-with-an-excessive-latency/
Potential PulseAudio version problem: PulseAudio is streaming with an excessive latency. Sound may be lost or quality degraded. To address that issue, upgrade the PulseAudio daemon to version 3.0, or disable the alternate sampling rate in its configuration. I can find /etc/pulse/daemon.conf and its man page , but cannot figure out what to do.
PulseAudio-15.0
https://www.linuxfromscratch.org/blfs/view/svn/multimedia/pulseaudio.html
After closing the application, close pulseaudio, either using pulseaudio --kill or, if that fails, killall -KILL pulseaudio and then rm -rf ~/.config/pulse/* (and perhaps also rm -rf ~/.pulse/* if you have used a very old version of pulse on this machine), then run pulseaudio --verbose to restart it. If the daemon starts, restart the application.
pulseaudio - What is a "Failed to load module "module ...
https://askubuntu.com/questions/325262/what-is-a-failed-to-load-module-module-ladspa-sink-error
Failed to initialize daemon. pulseaudio[3660]: main.c: Daemon startup failed Clearly the equalizer had left something behind when I removed it. Turned out the problem was in ~/.pulse/default.pa. The file had been modified in the install and not removed with it. The offending lines were at the end of the file. They looked like:
Pulseaudio daemon start up fails / Multimedia and Games ...
https://bbs.archlinux.org/viewtopic.php?id=159605
Re: Pulseaudio daemon start up fails Hi archers: sorry for the necrobump but I have the same problem with the same symptoms and wanted to now if some of you know the solution for this problem tried almost everything in my mind
How to install PipeWire on Ubuntu Linux - Linux Tutorials ...
https://linuxconfig.org/how-to-install-pipewire-on-ubuntu-linux
$ systemctl --user daemon-reload Use the following systemd command to re-enable the PulseAudio service. This command will start the service right now and also enable it to start automatically upon system reboots. $ systemctl --user --now enable pulseaudio.service pulseaudio.socket
[meta-freescale] how to install pulseaudio completely
https://yocto.yoctoproject.narkive.com/FRggZfEi/meta-freescale-how-to-install-pulseaudio-completely
fsl-image-gui to start up, i just find "libpulse*" in the. rootfs. I think that something wrong with pulseaudio configure so that it do not. install completely by default. The pulseaudio daemon is packaged as pulseaudio-server, maybe the image.
Now you know Pulseaudio Daemon 3.0
Now that you know Pulseaudio Daemon 3.0, we suggest that you familiarize yourself with information on similar questions.
