We have collected the most relevant information on Pulseaudio Digital Output. Open the URLs, which are collected below, and you will find all the info you are interested in.
Vanco PulseAudio Digital-Analog Audio Extender PA-EXTDA B&H
https://www.bhphotovideo.com/c/product/1536178-REG/vanco_pa_extda_pulseaudio_digital_analog_audio_extender.html#:~:text=Transmit%20Digital%20and%20analog%20audio%20over%20category%20cable,digital%20signals%20can%20be%20transmitted%20up%20to%20951.44%27.
PulseAudio - Official Kodi Wiki
https://kodi.wiki/view/PulseAudio
PulseAudio is used when Kodi is installed in a desktop-environment rather than a dedicated/direct boot setup. PulseAudio allows normal video & audio playback in XBMC while at the same time allowing the user to get audio in their browser or other applications. It also allows Kodi playback of video or audio to be paused in order to run a game, Skype or similar.
PulseAudio/Examples - ArchWiki - Arch Linux
https://wiki.archlinux.org/title/PulseAudio/Examples
Set the default output sink. To list the output sinks available, type the following command: $ pacmd list-sinks | grep -e 'name:' -e 'index:'. * index: 0 name: <alsa_output.pci-0000_04_01.0.analog-stereo> index: 1 name: <combined>. The * in front of the index indicates the current default output.
Configuring Pulseaudio for Multiple Output Devices - Eliot ...
http://www.6by9.net/configuring-pulseaudio-for-multiple-output-devices/
To re-configure Pulseaudio for audio out (to my headphones): #!/bin/sh /usr/bin/pacmd set-card-profile alsa_card.pci-0000_02_05.0 output:analog-stereo /usr/bin/pacmd set-sink-port alsa_output.pci-0000_02_05.0.analog-stereo analog-output\;output-headphones-2 echo Full Pulseaudio Configuration Output. lspci -vvv -s 02:05.0
PulseAudio has no sound, only has Dummy Output - Ask …
https://askubuntu.com/questions/1359038/pulseaudio-has-no-sound-only-has-dummy-output
>>> set-cart-profile 1 output:analog-stereo+input:analog-stereo No card found by this name or index. >>> set-sink-port 0 analog-output-headphones Failed to set sink port to 'analog-output-headphones'. Run below commands:(link here) pulseaudio --check pulseaudio -D Delete ~/.config/pulse followed by a reboot. Run below Commands:
Changing Output Device with PulseAudio - Reality's End
http://www.realitysend.com/log/linux/changing-output-device-with-pulseaudio
profiles: output:analog-stereo: Analog Stereo Output (priority 6000) output:analog-stereo+input:analog-stereo: Analog Stereo Duplex (priority 6060) output:hdmi-stereo: Digital Stereo (HDMI) Output (priority 5400) output:hdmi-stereo+input:analog-stereo: Digital Stereo (HDMI) Output + Analog Stereo Input (priority 5460) output:hdmi-surround: Digital Surround 5.1 …
What is the difference between Analog / Digital outputs in ...
https://forum.manjaro.org/t/what-is-the-difference-between-analog-digital-outputs-in-pulseaudio-control-panel/15617
Creative claims it can do 24-bit 96kHz. It can probably do the same in Linux, but I think it is more than most people need, and may not work well on a low-end system. Human range of hearing only goes up to 20kHz at the most. most people cannot hear any audible difference above 48kHz (but it may upset local bats!)
PulseAudio: the diff between Analog Output and Digital ...
https://www.reddit.com/r/linuxquestions/comments/e4iosb/pulseaudio_the_diff_between_analog_output_and/
Digital outputs leave the soundcard without the digital to analog conversion. These outputs are e.g. Spdif, Toslink, or hdmi. For these outputs the digital to analog conversion is done on the remote device. I know that the G6 supports digital Spdif over the line out jack. I don't know why it is much quieter, but this is the difference in theory.
PulseAudio - ArchWiki
https://wiki.archlinux.org/title/PulseAudio
MPlayer natively supports PulseAudio output with the -ao pulse option. It can also be configured to default to PulseAudio output, in ~/.mplayer/config for per-user, or /etc/mplayer/mplayer.conf for system-wide: /etc/mplayer/mplayer.conf ao=pulse mpv. mpv supports PulseAudio same as written for #MPlayer.
[SOLVED] Pulseaudio speaker-test. HDMI sound not working ...
https://forums.debian.net/viewtopic.php?t=149515
Code: Select all speaker-test 1.1.8 Playback device is hw:1,7 Stream parameters are 48000Hz, S16_LE, 2 channels Using 16 octaves of pink noise Rate set to 48000Hz (requested 48000Hz) Buffer size range from 64 to 524288 Period size range from 32 to 262144 Using max buffer size 524288 Periods = 4 was set period_size = 131072 was set buffer_size = 524288 0 - …
PulseAudio for analog/spdif hell – so simple, yet you have ...
https://blog.kanojo.de/2011/09/18/pulseaudio-for-analogspdif-hell-simple-yet-you-gotta-find-it/
You need some small piece of alsa configuration so pulseaudio can properly autodetect your spdif output as well as leverage alsas encoder to do the actual work. On any debian-like system (and probably others too) you can just install a *RECENT* pulseaudio (>= 0.9.23) along with pavucontrol and put this piece of config into your /etc/asound.conf
Now you know Pulseaudio Digital Output
Now that you know Pulseaudio Digital Output, we suggest that you familiarize yourself with information on similar questions.
