We have collected the most relevant information on Pulseaudio Input Source. Open the URLs, which are collected below, and you will find all the info you are interested in.
PulseAudio/Examples - ArchWiki
https://wiki.archlinux.org/title/PulseAudio/Examples
$ pactl load-module module-loopback source=input_source sink=output_source. This command will print the module's ID so that you can stop the piping later like this: $ pactl unload-module id. If you lose the ID, you can obtain it from pactl list modules short. PulseAudio as a minimal unintrusive dumb pipe to ALSA
audio - How to mix two input sources in Pulseaudio (for ...
https://unix.stackexchange.com/questions/681438/how-to-mix-two-input-sources-in-pulseaudio-for-recording-mic-and-speakers-with
Is there a way to create a virtual Pulseaudio source where the speakers and mic both go, so that I can then instruct SSR to record from that virtual source? As I read up at Mix application and microphone into one input, I can create a virtual speaker to which I can route both the mic and the speakers, and from which SSR can read. However, I ...
linux - Configure pulseaudio default input port - Unix ...
https://unix.stackexchange.com/questions/612215/configure-pulseaudio-default-input-port
For instance, pacmd set-card-profile 0 output:analog-stereo+input:analog-stereo. First list your cards, by pacmd list-cards, then set the card's profile by using pacmd set-card-profile 0 output:analog-stereo+input:analog-stereo where you can replace the '0' in the command by the card's index number. Try keeping the same profile as described in the command, i.e. …
linux - Pulseaudio set/check default source - Stack Overflow
https://stackoverflow.com/questions/59150186/pulseaudio-set-check-default-source
1.change /etc/pulse/client.conf, add following lines: default-sink = alsa_output.pci-0000_00_1b.0.hdmi-stereo default-source = alsa_input.pci-0000_00_1b.0.analog-stereo. 2.change /etc/pulse/default.pa, add following lines: ### Make some devices default set-default-source alsa_input.pci-0000_00_1b.0.analog-stereo.
How to Loopback Application Sound as an Input Source with ...
https://huma.id/blog/pulseaudio-loopback/
In the next command, replace <source> with the name of your source. pactl load-module module-loopback latency_msec=60 adjust_time=6 source=<source> sink=sink_mix Using PulseAudio Volume Control (pavucontrol), we can see we can now set the playback of specific applications to sink_mix instead of your default output source. You can also under recording, …
How to Use PulseAudio on Arch Linux
https://linuxhint.com/pulseaudio_arch_linux/
Start “PulseAudio Volume Control”. You can check out the playback and control its volume. At the “Recording” tab, there will be all the apps that are currently recording audio from any source (playback and/or recording hardware). At the “Output Devices” tab, you’ll notice all the devices that are currently available for outputting ...
Pulseaudio device names - OZ9AEC Website
https://oz9aec.net/software/gstreamer/pulseaudio-device-names
The interesting modules are those of type “Source #” for input and “Sink #” for playback. The pulseaudio device name is then the weird text string shown under the “Name” parameter. The Pulseaudio FAQ has some neat tricks for filtering the device names out: pactl list | grep -A2 'Source #' | grep 'Name: ' | cut -d" " -f2
Now you know Pulseaudio Input Source
Now that you know Pulseaudio Input Source, we suggest that you familiarize yourself with information on similar questions.
