We have collected the most relevant information on Pulseaudio Set Default Volume. Open the URLs, which are collected below, and you will find all the info you are interested in.
Set default pulseaudio volume - Ask Ubuntu
https://askubuntu.com/questions/476619/set-default-pulseaudio-volume
With PulseAudio 8.0 on Ubuntu 16.04 and a single sound card, you can set the default master volume to 50% with the following file. By including the system default you don't have to worry about changes in the distribution's defaults. $ cat ~/.config/pulse/default.pa .include /etc/pulse/default.pa # Set volume to 50% on boot set-sink-volume 0 32768
[SOLVED] Pulseaudio default volume.....
https://www.linuxquestions.org/questions/slackware-14/pulseaudio-default-volume-4175567844/
Since the most recent upgrade, which installed pulseaudio, I am unable to control the default (power-on) audio level. It always goes to 100%, resulting in a deafening login jingle!!! Previously, I would use alsamixer as root to set initial volumes. Although that still goes through the motions, the volumes reset to 100% on reboot.
How to set Pulseaudio default - antiX-forum
https://www.antixforum.com/forums/topic/how-to-set-pulseaudio-default/
go to preferences, under “Status icon”, “External mixer” you can write. pavucontrol. instead of alsamixer. Afterwards the volumeicon will open pavucontrol with a middle mouse click or under “Open mixer”. Besides all that, firefox will play sound without problems and without pulsaudio if you open it with the command.
How to control your Pulseaudio sound volume using the ...
https://securitronlinux.com/debian-testing/how-to-control-your-pulseaudio-sound-volume-using-the-command-line/
This is a very easy way to control a Pulseaudio device on Linux. This is how to reduce the sound volume for Pulseaudio. jason@jason-desktop:~$ pactl set-sink-volume 1 - 45%. jason@jason-desktop :~$ pactl set-sink-volume 1 -45%.
Set default profile for PulseAudio - Unix & Linux Stack ...
https://unix.stackexchange.com/questions/462670/set-default-profile-for-pulseaudio
from the command line to see if it sets the profile correctly, then add it to /etc/pulse/default.pa. Since the index name is dynamic (it can change your PCI device index if you boot with a USB audio device plugged in), you could use <symbolic-name> instead of <index> (if you run pacmd list-cards, the symbolic name is right below the index). Also, the command …
Pulseaudio: setting volume from command line | …
https://blog.waan.name/pulseaudio-setting-volume-from-command-line/
pactl set-sink-volume @DEFAULT_SINK@ -- +10% (the characters ‘--’ can be omitted in this case) [minus] pactl set-sink-volume @DEFAULT_SINK@ -- -10% [mute] pactl set-sink-mute @DEFAULT_SINK@ toggle. pd: Sorry if my english is not good. I speak spanish :)
PulseAudio/Examples - ArchWiki - Arch Linux
https://wiki.archlinux.org/title/PulseAudio/Examples
Tip: The default sink can be referred as @DEFAULT_SINK@ in commands, for example: $ pactl set-sink-volume @DEFAULT_SINK@ +5%. Set the default output sink profile Sometimes PulseAudio neglects to load the desired profile on start (e.g. a profile for having #Independent analog and digital outputs on the same card ).
PulseAudio: Play samples at a set volume - Stack Overflow
https://stackoverflow.com/questions/47729914/pulseaudio-play-samples-at-a-set-volume
The issue is that when the volume is very low or very high, the sound effects (button press bleeps, etc.) are also too weak or too loud. The Raspberry Pi uses PulseAudio (system daemon), and this is its PulseAudio set-up: I play the samples, using: This command can take an additional parameter, namely the PulseAudio sink on which to play.
[Solved] PulseAudio can't remember default device after ...
https://bbs.archlinux.org/viewtopic.php?id=164868
Recently I updated pulseaudio to 4.0, and I found that my default output device was set to HDMI output. Because I wanted to use Analog output, I change it in the gnome settings. But after I logouted and logined, the output device was set to HTML output again. I have tried to add set-defualt-sink in /etc/pulse/defualt.pa but it didn't work.
Now you know Pulseaudio Set Default Volume
Now that you know Pulseaudio Set Default Volume, we suggest that you familiarize yourself with information on similar questions.
