We have collected the most relevant information on Pulseaudio Sound Crackling. Open the URLs, which are collected below, and you will find all the info you are interested in.
pulseaudio - Skype and VLC sounds sizzling, distorted, bad ...
https://askubuntu.com/questions/157891/skype-and-vlc-sounds-sizzling-distorted-bad-crackling#:~:text=To%20do%20this%2C%20edit%20the%20%2Fetc%2Fpulse%2Fdefault.pa%20file%20in,your%20system%29%2C%20and%20the%20crackling%20should%20be%20gone.
audio - How to fix crackling sound in PulseAudio ...
https://elementaryos.stackexchange.com/questions/13909/how-to-fix-crackling-sound-in-pulseaudio
How to fix crackling sound in PulseAudio. Ask Question Asked 4 years, 2 months ago. Active 3 years, 8 months ago. Viewed 10k times 1 1. I have been experiencing a crackling sound after enabling the PulseAudio Equalizer. sound audio. Share. Improve this …
10.10 - crackling audio with Pulseaudio - Ask Ubuntu
https://askubuntu.com/questions/10173/crackling-audio-with-pulseaudio
The problem is usually caused by bad latency and incorrectly set frequency settings in Pulse Audio. it's possible to fix but disabling pulse audio is probably something to look into too. See this article about all your sound options: https://help.ubuntu.com/community/UbuntuStudioPreparation
[SOLVED] Crackling sound with pulseaudio / Multimedia and ...
https://bbs.archlinux.org/viewtopic.php?id=170824
open paprefs, go to Simultanous Output tab and enable it. then go to your volume control and change the output to Simultaneous and check if the sounds still crackling. also would be nice if you post your /etc/pulse/daemon.conf. I tried paprefs with the simultaneous output enabled and it was still doing that.
Crackling sounds with pulseaudio - but only sometimes ...
https://www.reddit.com/r/archlinux/comments/skr1z2/crackling_sounds_with_pulseaudio_but_only/
Crackling sounds with pulseaudio - but only sometimes. Close. 1. Posted by 1 day ago. Crackling sounds with pulseaudio - but only sometimes. Hey there, as I described in this post a few months back, I still sometimes have problems with distorted …
Finally fixed crackling audio when passing through ...
https://www.reddit.com/r/VFIO/comments/ibmjs3/finally_fixed_crackling_audio_when_passing/
Finally fixed crackling audio when passing through PulseAudio to QEMU with Win10 guest For whatever reason, Windows' audio output frequency (right-click the sound icon -> Open sound settings -> Sound Control Panel -> right-click the HD Audio device -> Properties -> Advanced) needed to be set to exactly half of what was set in the virsh configuration file.
Why is the audio crackling? I can fix by typing ...
https://www.reddit.com/r/linuxmint/comments/qapdeu/why_is_the_audio_crackling_i_can_fix_by_typing/
If you don't want to type in everytime pulseaudio -k , there is a permanent solution. you type in the terminal: sudo gedit /etc/pulse/default.pa. then you have to find the line "load-module module-udev-detect" and disable it with a #. You go a line below and type in "load-module module-udev-detect tsched=0"
Ha! Got rid of the pulse audio crackling! : VFIO
https://www.reddit.com/r/VFIO/comments/542bw1/ha_got_rid_of_the_pulse_audio_crackling/
Got rid of the pulse audio crackling! Hi folks, after almost giving up and trying almost every combination of QEMU_PA_SAMPLES with different combinations of fragment sizes in pulseaudio/daemon.conf and nothing helping the slightest bit, I found the setting that really helps: <qemu:commandline> <qemu:env name='QEMU_AUDIO_DRV' value='pa'/> <qemu:env …
Crackle-free audio on the Raspberry Pi with mpd and PulseAudio
https://dbader.org/blog/crackle-free-audio-on-the-raspberry-pi-with-mpd-and-pulseaudio
Restart PulseAudio and mpd to let the configuration changes take effect. You do this by running the following two commands: sudo /etc/init.d/pulseaudio restart sudo /etc/init.d/mpd restart. These steps completely fix the audio crackles and pops …
pulseaudio - Crackling sound with usb interface - Unix ...
https://unix.stackexchange.com/questions/561706/crackling-sound-with-usb-interface
So this is a super wild guess, but it sounds like as if it tries to output those samples that are in the buffer, which happens faster than it should be due to mismatching sample rates, but then the buffer is empty and it has to wait for more samples to accumulate, which produces the distortion. EDIT: see Pulseaudio detects wrong sample rate. Forcing pulseaudio a sample rate
Now you know Pulseaudio Sound Crackling
Now that you know Pulseaudio Sound Crackling, we suggest that you familiarize yourself with information on similar questions.
