We have collected the most relevant information on Raspbmc Pulseaudio Setup. Open the URLs, which are collected below, and you will find all the info you are interested in.
How to use pulseaudio for network stream with Raspbmc ...
https://itectec.com/unixlinux/how-to-use-pulseaudio-for-network-stream-with-raspbmc-kodi/
1. Install pulseaudio. sudo apt-get install pulseaudio pulseaudio-module-zeroconf 2. Setting up pulseaudio. sudo nano /etc/pulse/default.pa I added the following lines: load-module module-native-protocol-unix auth-anonymous=1 load-module module-native-protocol-tcp auth-ip-acl=127.0.0.1;192.168.1.0/24 auth-anonymous=1 load-module module-zeroconf-publish 3. …
How to use pulseaudio for network stream with Raspbmc ...
https://unix.stackexchange.com/questions/176815/how-to-use-pulseaudio-for-network-stream-with-raspbmc-kodi
I am using Raspbmc (with Kodi 14) on my Raspberry Pi. Now I would like to set up pulseaudio to be able to stream music from all my Linux computers easily to the Raspberry pi. My problem is, that I am not able to get pulseaudio running on the Raspberry Pi. I tried the following steps: 1. Install pulseaudio
Setting up MPD on a Raspberry PI with a RaspBMC ...
https://felipedelamuerte.wordpress.com/2013/01/05/setting-up-mpd-on-a-raspberry-pi-with-a-raspbmc-installation/
All this is done on a fresh install of RaspBMC RC5 / XBMC RC2, as released on the 30th of December. The steps are fairly straight-forward. Let’s start with enabling sound output through ALSA and PulseAudio: sudo modprobe snd_bcm2835. Furthermore we’ll add “snd_bcm2835” (without the parentheses) to /etc/modules, so it will be loaded on startup.
Crackle-free audio on the Raspberry Pi with mpd and …
https://dbader.org/blog/crackle-free-audio-on-the-raspberry-pi-with-mpd-and-pulseaudio
Install PulseAudio by running sudo apt-get install pulseaudio; Configure mpd to use PulseAudio as output plugin by editing /etc/mpd.conf. You need to remove or comment out the lines that refer to the Alsa output plugin and add these lines instead:
audio - How to set up a PulseAudio sink? - Raspberry Pi ...
https://raspberrypi.stackexchange.com/questions/8621/how-to-set-up-a-pulseaudio-sink
So (as root, or sudo): chmod u+s /usr/bin/pulseaudio. There is no pulse-rt group created when pulseaudio is installed on raspbian, so then: groupadd pulse-rt. This will give you a gid like 1003. Add (e.g.) user pi to that group: usermod -aG pulse-rt …
audio - PulseAudio does not detect sound cards on …
https://stackoverflow.com/questions/18902761/pulseaudio-does-not-detect-sound-cards-on-raspbmc
You likely need to load the kernel module for the sound device, like this: # modprobe snd-bcm2835. That will cause some new device files to appear in /dev/snd/ that pulseaudio will detect as Card #0. If I understand it correctly, this device is a …
Enhance Raspberry Pi Media Center With Bluetooth A2DP ...
https://www.instructables.com/Enhance-your-Raspberry-Pi-media-center-with-Blueto/
Execute these two commands to scan for new/changed units and to restart the PulseAudio service: sudo systemctl daemon-reload sudo systemctl enable pulseaudio.service sudo systemctl start pulseaudio.service. All that is left to do for audio is to enable output to a prefered connector (0=auto,1=headphones,2=hdmi): amixer cset numid=3 1
How to install Raspbmc on Raspberry Pi?
https://www.smarthomebeginner.com/install-raspbmc-on-raspberry-pi/
Based on popular request, here is the guide to install Raspbmc on Raspberry Pi. If you have been following me you may already know that I have been a fan of OpenELEC on Raspberry Pi.Well that changed recently after my latest comparison of Raspbmc and OpenELEC.I quickly started feeling very restricted on OpenELEC and found the ability to install Debian …
Networked Speaker/ USB Soundcard - Raspberry Pi Forums
https://forums.raspberrypi.com/viewtopic.php?t=6493
I created a pulseaudio firmware or TP-Link WR703N (up to v 1.5) early this year so you could just flash it to WR703N and it would work with most usb soundcard/speakers and its plug and play. If you could install pulseaudio on your pi or build puleaudio support into xbmc you could stream audio throughout your house.
MonkeyHouse: A2DP Audio on Raspberry Pi
https://kmonkey711.blogspot.com/2012/12/a2dp-audio-on-raspberry-pi.html
pi@raspberrypi ~ $ sudo apt-get install bluez pulseaudio-module-bluetooth python-gobject python-gobject-2. Add the user pi to the group lp. This is so the user pi can get access to the bluetooth daemon. If this isn't done, the bluez source will not show up in pulse audio. pi@raspberrypi ~ $ sudo usermod -a -G lp pi.
Now you know Raspbmc Pulseaudio Setup
Now that you know Raspbmc Pulseaudio Setup, we suggest that you familiarize yourself with information on similar questions.
