We have collected the most relevant information on Wsjt Virtual Audio Cable. Open the URLs, which are collected below, and you will find all the info you are interested in.
How to Configure WSJT with PowerSDR and VAC - FlexRadio
http://kc.flex-radio.com/KnowledgebaseArticle50362.aspx
Since the PowerSDR VAC input ( VAC virtual cable 1 ) needs to receive audio from the WSJT output, we need to select audio device 9 for the WSJT output . WSJT Input = VAC Output (virtual cable 2) = Audio Device #4 WSJT Output = VAC Input (virtual cable1) = …
https://wsjtx.groups.io/g/main/topic/sound_and_virtual_audio_cable/71518601?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,0,71518601
Sound and Virtual Audio Cable; ... I have set the audio input in WSJT-X to VAC Line 1. This works just fine. My issue is this: I am hearing the audio coming out of the speakers as well, of course, since WSJT-X audio output is set to speakers. There …
Using SDR-Radio (SDR Console) and Wsjt-X (Examples of ...
http://www.hamskey.com/2018/04/using-sdr-radio-sdr-console-and-wsjt-x.html
SDR-Console and Wsjt-X are transmitted through a virtual audio cable. In other words, the signal received from RTL-SDR will be delivered immediately to Wsjt-x without using a separate sound card. To do this we need to install the Virtual Audio cable. The Virtual Audio cable has a wide variety of products.
How to Setup Virtual Audio Cable (VAC) 4.0x with PowerSDR
https://helpdesk.flexradio.com/hc/en-us/articles/206605196-How-to-Setup-Virtual-Audio-Cable-VAC-4-0x-with-PowerSDR
Virtual Audio Cable (VAC) is a third-party software program that allows the rerouting and the emulation of a sound card in software rather than having to use a second sound card for audio analysis or use with digital mode programs such as MixW and WSJT. There are some significant advantages to using VAC over a second sound card.
Audio Configuration - wfview
https://wfview.org/wfview-user-manual/audio-configuration/
In wfview, Audio Output should be “Line 1 (Virtual Audio Cable” and Audio Input “Line 2 (Virtual Audio Cable)”. In your software, for example WSJT-X, under the Audio tab, Input wants to be “Line 1 (Virtual Audio Cable)” and Output “Line 2 (Virtual Audio Cable)”. Basically, the output of wfview connects to the input of WSJT-X and the output of WSJT-X connects to the input of wfview. …
Setting up CAT/CI-V and Audio Drivers for WSJT-X
https://www.n1fd.org/2018/11/26/wsjt-x-setup/
WSJT-X uses a small set of messages over the CAT interface to control the radio. These include band changing, VFO frequency, PTT and a few others. The USB UART Bridge requires a VCP driver that must be installed by you before connecting the radio to the PC.
Using WSJT-X with SDRUNO and RSP1A - VE6KQ
http://www.ve6kq.com/wsjtandsdruno.pdf
following should be done in order otherwise there is a good change WSJT-X won’t run. See screen shots below for support of the following steps. You will need to run the Virtual Serial Port Emulator (VSPE) first. Next install SDRUNO. Verify that the RX setting, OUT Tab, on the RX Control is set to Virtual Cable. In my case it’s VB-Audio. On the CAT Tab, I use com5 and a BAUD RATE …
WSJT-X integration with your SDR program
http://radiosrs.net/digital_modes.html
CubicSDR/WSJT-X integration. Start the Virtual0 virtual audio cable device in a terminal as follows: pacmd load-module module-null-sink sink_name=Virtual0 pacmd update-sink-proplist Virtual0 device.description=Virtual0 pacmd update-source-proplist Virtual0.monitor device.description=Virtual0 Start rigctld in a terminal:
Now you know Wsjt Virtual Audio Cable
Now that you know Wsjt Virtual Audio Cable, we suggest that you familiarize yourself with information on similar questions.